Online
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to BOX in BROM mode
Wait for device... OK
Read usbhost speed... FULL
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 6580
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6580]
Get sec config... OK [00000007]
Active sec flags: [SBC SLA DAA]
Advanced Bypass Security... OK
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM135 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 6580
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6580]
Library Version [1]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Load DownloadAgent... OK
ME_ID = 0xAE6A790A, 0x79A089A1, 0xADDEAFFE, 0x2EAEDE99
Get sec config... OK [00000000]
Get BROM version... OK
Search DA... OK [11]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Check bootloader answer... OK
Wait for answer from bootloader... OK
Wait for hw detection... OK
Wait DA version... v4.2
Send BROM version... OK
Send storage config... OK
SyncBmtInfoWithDA... OK
Set params... OK
Read flash info... OK
EMMC_ID: 0x4403018836314439C42A6547D5370769
Load EMI from phone... OK
Init DRAM... OK
Enable DRAM... OK
Sync with DA... OK
Wait for DA H/W detection... OK
EMMC INFO:
EMMC_ID : 0x880103443944313647652AC4690737D5
EMMC_BOOT1: 0x0000400000 (4,00Mb)
EMMC_BOOT2: 0x0000400000 (4,00Mb)
EMMC_RPMB : 0x0000400000 (4,00Mb)
EMMC_USER : 0x039D000000 (14,45Gb)
RAM INFO:
INT_SRAM: 0x0000020000 (128,00Kb)
EXT_RAM : 0x0040000000 (1,00Gb)
Check USB status... USB_FULL_SPEED
Switching to USB high speed... OK
Wait for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek DA USB VCOM (Android),usb2ser.sys,3.0.1504.0]
High Speed USB detected at COM240
Open port... OK
Check USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Read product info... OK
Product Brand : TCL
Product Manufacturer : TCL
Product Model : 9009G
Product Name : 9009G
Product Device : U3A_7_3G
Product Board : u3a3gvf
Board Platform : MT6580
Build ID : O11019
Build Date : Mon Aug 12 20:11:35 CST 2019
Security Patch : 2019-06-05
Version SDK : 27
Version Release : 8.1.0
Version Codename : REL
Firmware Version : vJ65-0
Read security partition from phone... OK
Read security files... OK
Read security files... OK
Read lock info... OK
Write lock info... OK
Write security partition to phone... OK
Network Unlock done!
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to BOX in BROM mode
Wait for device... OK
Read usbhost speed... FULL
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 6580
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6580]
Get sec config... OK [00000007]
Active sec flags: [SBC SLA DAA]
Advanced Bypass Security... OK
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM135 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 6580
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6580]
Library Version [1]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Load DownloadAgent... OK
ME_ID = 0xAE6A790A, 0x79A089A1, 0xADDEAFFE, 0x2EAEDE99
Get sec config... OK [00000000]
Get BROM version... OK
Search DA... OK [11]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Check bootloader answer... OK
Wait for answer from bootloader... OK
Wait for hw detection... OK
Wait DA version... v4.2
Send BROM version... OK
Send storage config... OK
SyncBmtInfoWithDA... OK
Set params... OK
Read flash info... OK
EMMC_ID: 0x4403018836314439C42A6547D5370769
Load EMI from phone... OK
Init DRAM... OK
Enable DRAM... OK
Sync with DA... OK
Wait for DA H/W detection... OK
EMMC INFO:
EMMC_ID : 0x880103443944313647652AC4690737D5
EMMC_BOOT1: 0x0000400000 (4,00Mb)
EMMC_BOOT2: 0x0000400000 (4,00Mb)
EMMC_RPMB : 0x0000400000 (4,00Mb)
EMMC_USER : 0x039D000000 (14,45Gb)
RAM INFO:
INT_SRAM: 0x0000020000 (128,00Kb)
EXT_RAM : 0x0040000000 (1,00Gb)
Check USB status... USB_FULL_SPEED
Switching to USB high speed... OK
Wait for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek DA USB VCOM (Android),usb2ser.sys,3.0.1504.0]
High Speed USB detected at COM240
Open port... OK
Check USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Read product info... OK
Product Brand : TCL
Product Manufacturer : TCL
Product Model : 9009G
Product Name : 9009G
Product Device : U3A_7_3G
Product Board : u3a3gvf
Board Platform : MT6580
Build ID : O11019
Build Date : Mon Aug 12 20:11:35 CST 2019
Security Patch : 2019-06-05
Version SDK : 27
Version Release : 8.1.0
Version Codename : REL
Firmware Version : vJ65-0
Read security partition from phone... OK
Read security files... OK
Read security files... OK
Read lock info... OK
Write lock info... OK
Write security partition to phone... OK
Network Unlock done!
