💭Duda*Consulta Ayuda Oppo Reno 2Z (CPH1945) luego de flashar solo vibra

[servergsm]

alguien me puede ayudar por error flashe un firmware a Oppo Reno 2Z (CPH1945) y ahora esta brik muerto alguien tiene un firmware que puede revivirlo

Can someone help me? I accidentally flashed the wrong firmware to my Oppo Reno 2Z (CPH1945) and now it's bricked. Does anyone have a firmware that can fix it?

dejare el registo trata con pandora y aun solo vibra
​

here is the last logs:
Extracting scatter file... OK
Parse scatter file... OK
Connect Type-C to NONE... OK
Host Power Off... OK
Connect phone to [PC] in BROM Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM5 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0725
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA01, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6779]
LibUSB installed
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Release testpoint, waiting 2 seconds
Advanced Bypass Security... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM5 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0725
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA01, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6779]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x6EDE2C29, 0x911039B9, 0x854FF157, 0xBA451C5B
Get Chip ID... [MT6779]
Get SOC ID... [F86FB56924CB11B541E8F4FEF3DF3F581D5A67BA71BA8EEB11 7C661DED3D6034]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [10]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): KM8B8001JM-BC01 (0600)
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : KM8B8001JM-BC01
UFS_FWVER : 0600
BLOCK_SIZE: 0x0000001000 (4.00Kb)
UFS_LU0 : 0x0000400000 (4.00Mb)
UFS_LU1 : 0x0000400000 (4.00Mb)
UFS_LU2 : 0x3B96000000 (238.34Gb)
RAM INFO:
INT_SRAM: 0x0000080000 (512.00Kb)
EXT_RAM : 0x0200000000 (8.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 10% - 20% device life time used
DeviceLifeTimeEstB: 10% - 20% device life time used
Get scatter info... OK
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... error(3)
Prepare list for upgrade... OK
Checking upgrade list... OK
Prepare format list... OK
Prepare final partition list... OK
Read partition "preloader"... OK
Read partition "opporeserve1"... OK
Read partition "opporeserve2"... OK
Read partition "opporeserve3"... OK
Read partition "oppo_custom"... OK
Read partition "nvcfg"... OK
Read partition "protect1"... OK
Read partition "protect2"... OK
Read partition "persist"... OK
Read partition "proinfo"... OK
Read partition "nvram"... OK
Verify checksum... OK
Format "UFS_LU2" partition( 0x00008000..0x04107FFF )... OK
Format "UFS_LU2" partition( 0x0CA08000..0x0E707FFF )... OK
Format "UFS_LU2" partition( 0x10708000..0x16707FFF )... OK
Format "UFS_LU2" partition( 0x17800000..0x1787FFFF )... OK
Format "UFS_LU2" partition( 0x1B000000..0x1B1FFFFF )... OK
Format "UFS_LU2" partition( 0x1F500000..0x357FFFFF )... OK
Format "UFS_LU2" partition( 0x45800000..0x3165A01FFF )... OK
Get scatter info... OK
Verify scatter file... OK
Do NAND BMT remark... OK
Setup download info... OK
Get partition table catagory... OK [GPT]
Read mirror partition table... OK
Generate mirror partition table... OK
Downloading mirror partition table... OK
Read major partition table... OK
Checking major partition table layout changed... OK
Generate major partition table... OK
Downloading major partition table... OK
Download "preloader"... OK
Download "recovery"... OK
Download "opporeserve2"... OK
Download "vbmeta"... OK
Download "md1img"... OK
Download "spmfw"... OK
Download "audio_dsp"... OK
Download "scp1"... OK
Download "scp2"... OK
Download "sspm_1"... OK
Download "sspm_2"... OK
Download "cam_vpu1"... OK
Download "cam_vpu2"... OK
Download "cam_vpu3"... OK
Download "gz1"... OK
Download "gz2"... OK
Download "lk"... OK
Download "lk2"... OK
Download "boot"... OK
Download "logo"... OK
Download "dtbo"... OK
Download "tee1"... OK
Download "tee2"... OK
Download "vendor"... OK
Download "system"... OK
Download "cache"... OK
Download "userdata"... OK
Download "PROJECT ID"... OK
Flashing done!


Selected model: OPPO CPH1945 (OPPO Reno2 Z)
Operation: Write OFP
Software version: 9.4