Admin
Offline
- Marca 📱
- Otras Marcas
- Modelo 🔖
- BLU M10L Pro
- Tipo de falla / servicio 🛠️
- FRP / Desbloqueos (cuentas, IMEI, red)
- Estado del equipo 📋
- Bloqueado (Contraseña o cuenta Google) FRP O Hart Reset
Eliminar Cuenta Google FRP A BLU M10L Pro con pandora box
Debes estar registrado para ver imágenes adjuntar
Código:
Selected model: BLU M10L Pro
Operation: Erase FRP And Wipe
Software version: 9.17
Erasing of partitions can damage your device.
Make sure that you have a backup created. Continue? YES
Host Power Off... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Host Power On... OK
Connect phone to [BOX] in BROM/PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek PreLoader USB VCOM (Android),usb2ser.sys,3.0.1504.0]
Device found at COM136 [PRELOADER]
Open port... OK
Send start cmd... OK
Get HW code from device... 0717
Get sec config... OK [00000005]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA01, SW VER: 0200, HW SUB CODE: 8A00
Detect chip [MT6761]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Force switch to BROM... OK
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Waiting for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0717
Get HW & SW version from device... OK
HW VER: CA01, SW VER: 0200, HW SUB CODE: 8A00
Detect chip [MT6761]
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Release testpoint
Advanced Bypass Security... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM191 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0717
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA01, SW VER: 0200, HW SUB CODE: 8A00
Detect chip [MT6761]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x02108A14, 0xB693070B, 0xA48EDF01, 0xE09096F2
Get Chip ID... [MT6761]
Get SOC ID... [4A128B337C4C96C07F67527642DCAA78686280827BA955DB458D17EEC474CC95]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [5]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x04010149534F434F4D10CE1520E06A19
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: ISOCOM
EMMC_ID : 0x04010149534F434F4D10CE1520E06A19
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x0749000000 (29.14Gb)
RAM INFO:
INT_SRAM: 0x000003A500 (233.25Kb)
EXT_RAM : 0x00C0000000 (3.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 80% - 90% device life time used
DeviceLifeTimeEstB: info not available
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK [A]
Read product info... [EXT4] ... OK
Product Brand : BLU
Product Manufacturer : BLU
Product Model : M10L Pro
Product Name : M10L_Pro
Product Device : M0215_ND
Product Board : q864_8766_64_t
Board Platform : mt6761
Build ID : SP1A.210812.016
Build Date : Fri Jun 20 20:58:48 CST 2025
Display ID : BLU_M0215_ND_V13.0.04.22_GENERIC 20-06-2025 20:58
Security Patch : 2025-06-05
Version SDK : 33
Version Release : 13
Version Codename : REL
Firmware Version : YM14002U
Userdata FS Type : EXT4
Read partition "frp"... OK
Backup saved to C:/Program%20Files%20(x86)/Z3X/Pandora/Backup/MTK/BLU_M10L%20Pro/FRP_BACKUP_(2026-2-10_11-56-55)/
Format FRP... [P1] OK
Writting FRP data... OK
Formatting "userdata" partition... [P1] OK
Formatting "metadata" partition... [P1] OK
Formatting "md_udc" partition... [P1] OK
Wipe data done!