Offline
Alcatel 5049w reparar imei con pandora box
Selected model: Alcatel 5049W (REVVL)
Operation: Repair
Software version: 3.4
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to BOX in BROM mode
Wait for device... OK
Read usbhost speed... FULL
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0326
Get HW & SW version from device... OK
HW VER: CB00, SW VER: 0001, HW SUB CODE: 8A00
Detect chip [MT6755]
Get sec config... OK [00000007]
Active sec flags: [SBC SLA DAA]
Advanced Bypass Security... OK
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [Microsoft,usbser,Dispositivo serie USB,usbser.sys,10.0.22000.1]
Device found at COM117 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0326
Get HW & SW version from device... OK
HW VER: CB00, SW VER: 0001, HW SUB CODE: 8A00
Detect chip [MT6755]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xA2A24EF2, 0x0EC5135C, 0x1A5FC4A7, 0x3FF0816E
Get Chip ID... [MT6750]
Get sec config... OK [00000000]
Modem count: 6
Load DownloadAgent... OK
Search DA... OK [2]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x150100515831334D4207A969FC3E94CF
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_ID : 0x150100515831334D4207A969FC3E94CF
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0000400000 (4.00Mb)
EMMC_USER : 0x0747C00000 (29.12Gb)
RAM INFO:
INT_SRAM: 0x0000038000 (224.00Kb)
EXT_RAM : 0x0080000000 (2.00Gb)
Check USB status... USB_FULL_SPEED
Switching to USB high speed... OK
Wait for device... OK
Driver: [MediaTek Inc.,usbser,DA USB VCOM Port,usbser.sys,10.0.22000.1]
High Speed USB detected at COM124
Open port... OK
Check USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Check A/B state... OK
Read product info... error(3)
Read OTP... OK
IMEI: 014976003738742
Set new IMEI to:
IMEI: 014976003719890
Check OTP status... [STATUS_OTP_LOCKED]
Write OTP... OK
Repair Security done!
Selected model: Alcatel 5049W (REVVL)
Operation: Repair
Software version: 3.4
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to BOX in BROM mode
Wait for device... OK
Read usbhost speed... FULL
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0326
Get HW & SW version from device... OK
HW VER: CB00, SW VER: 0001, HW SUB CODE: 8A00
Detect chip [MT6755]
Get sec config... OK [00000007]
Active sec flags: [SBC SLA DAA]
Advanced Bypass Security... OK
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [Microsoft,usbser,Dispositivo serie USB,usbser.sys,10.0.22000.1]
Device found at COM117 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0326
Get HW & SW version from device... OK
HW VER: CB00, SW VER: 0001, HW SUB CODE: 8A00
Detect chip [MT6755]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xA2A24EF2, 0x0EC5135C, 0x1A5FC4A7, 0x3FF0816E
Get Chip ID... [MT6750]
Get sec config... OK [00000000]
Modem count: 6
Load DownloadAgent... OK
Search DA... OK [2]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x150100515831334D4207A969FC3E94CF
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_ID : 0x150100515831334D4207A969FC3E94CF
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0000400000 (4.00Mb)
EMMC_USER : 0x0747C00000 (29.12Gb)
RAM INFO:
INT_SRAM: 0x0000038000 (224.00Kb)
EXT_RAM : 0x0080000000 (2.00Gb)
Check USB status... USB_FULL_SPEED
Switching to USB high speed... OK
Wait for device... OK
Driver: [MediaTek Inc.,usbser,DA USB VCOM Port,usbser.sys,10.0.22000.1]
High Speed USB detected at COM124
Open port... OK
Check USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Check A/B state... OK
Read product info... error(3)
Read OTP... OK
IMEI: 014976003738742
Set new IMEI to:
IMEI: 014976003719890
Check OTP status... [STATUS_OTP_LOCKED]
Write OTP... OK
Repair Security done!
