Una vez elegido el modelo en mi caso seleccione la opcion "forzar modo brom" y se conecta apagado precionando vol-
Selected model: Lg Q730AM (Lg Stylo 6)
Operation: Erase FRP And Wipe
Software version: 8.9
Erasing of partitions can damage your device.
Make sure that you have a backup created. Continue? YES
Host Power Off... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Host Power On... OK
Connect phone to [BOX] in BROM/PRELOADER Mode
Waiting for device... OK
Driver: [LG Electronics Inc.,UsbDiag,LGE Mobile USB Serial Port,lgx64diag.sys,5.3.0.0]
You are using driver version 5.3.0.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM17 [PRELOADER]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [00000005]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Force switch to BROM... OK
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Waiting for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0766
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Release testpoint
Advanced Bypass Security... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM6 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xA4A3A2AF, 0xA875ED9A, 0xB29971FF, 0x3F411D9C
Get Chip ID... [MT6765]
Get SOC ID... [1DF5B7E9C0B8D03398C8A7CF5F5F1C909631516452ADE61335A181196722FD19]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [7]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x13014E47314A395038100583F83757F5
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: G1J9P8
EMMC_ID : 0x13014E47314A395038100583F83757F5
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x0E8F800000 (58.24Gb)
RAM INFO:
INT_SRAM: 0x000003A000 (232.00Kb)
EXT_RAM : 0x00C0000000 (3.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 0% - 10% device life time used
DeviceLifeTimeEstB: 0% - 10% device life time used
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK [A]
Read product info... [EXT4] ... OK
Product Brand : lge
Product Manufacturer : LGE
Product Model : LM-Q730
Product Name : mdh50lm
Product Device : mdh50lm
Product Board : mt6765
Board Platform : mt6765
Build ID : QKQ1.200216.002
Build Date : Sat Apr 24 04:18:56 KST 2021
Security Patch : 2021-05-01
Version SDK : 29
Version Release : 10
Version Codename : REL
Firmware Version : 2111404201d79
Userdata FS Type : EXT4
Read partition "frp"... OK
Backup saved to C:/Program%20Files%20(x86)/Z3X/Pandora/Backup/MTK/Lg_Q730AM%20(Lg%20Stylo%206)/FRP_BACKUP_(2025-5-3_18-8-38)/
Format FRP... [P1] OK
Writting FRP data... OK
Formatting "userdata" partition... OK
Formatting "metadata" partition... OK
Formatting "md_udc" partition... OK
Wipe data done!
