Online
cuenta google Tecno CE9 (Tecno Camon 16 Premier) frp
Selected model: Tecno CE9 (Tecno Camon 16 Premier)
Operation: Eliminar FRP
Software version: 6.2
Host Power Off... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Host Power On... OK
Connect phone to [BOX] in BROM/PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM51 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0813
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6785]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Force switch to BROM... OK
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Waiting for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0813
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6785]
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Release testpoint
Advanced Bypass Security... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM51 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0813
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6785]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x6D8388EE, 0xA286CA1D, 0xE99F2CBA, 0xD45489E1
Get Chip ID... [MT6785]
Get SOC ID... [5DEDFC66C176F57BFED835A5E385EBE0FA52BFFC5085FDBDF0 52D59E14842553]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [12]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): H9HQ15AFAMADAR (A102)
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : H9HQ15AFAMADAR
UFS_FWVER : A102
BLOCK_SIZE: 0x0000001000 (4,00Kb)
UFS_LU0 : 0x0000400000 (4,00Mb)
UFS_LU1 : 0x0000400000 (4,00Mb)
UFS_LU2 : 0x1DCB000000 (119,17Gb)
RAM INFO:
INT_SRAM: 0x0000080000 (512,00Kb)
EXT_RAM : 0x0200000000 (8,00Gb)
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EXT4] ... OK
Product Brand : TECNO
Product Manufacturer : TECNO MOBILE LIMITED
Product Model : TECNO CE9
Product Name : CE9-OP
Product Device : TECNO-CE9
Product Board : TECNO-CE9
Board Platform : mt6785
Build ID : RP1A.200720.011
Build Date : Fri Sep 23 15:11:13 CST 2022
Display ID : CE9-H851ABC-R-GL-220923V475
Firmware Version : 220923V254
Userdata FS Type : F2FS
Read partition "frp"... OK
Backup saved to C:/Program%20Files%20(x86)/Z3X/Pandora/Backup/MTK/Tecno_CE9%20(Tecno%20Camon%2016%20Premier)/FRP_BACKUP_(2023-12-24_17-17-13)/
Writting FRP data... OK
Erase FRP done!
