Que tal colegas si ya hay algun tema borrarlo.
Sale muy sencillo con pandora box, colocan el cable tipo C directo a la box
Seleccionan MTK, seleccione BROM Force (no intente sin este)
Seleccionan IMEI
Colocan el nuevo imei
Seleccionan Reparar
Conectan Botones de VOL+ y VOL-
EL proceso se hace solo.
Dejo LOG:
Selected model: Mediatek Mediatek
Operation: Repair
Software version: 5.0
Host Power Off... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Host Power On... OK
Connect phone to [BOX] in BROM/PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM20 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0788
Get sec config... OK [000000E1]
Active sec flags: [SBC]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6771]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Force switch to BROM... OK
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Waiting for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0788
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6771]
Get sec config... OK [000000E1]
Active sec flags: [SBC]
Release testpoint
Advanced Bypass Security... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM20 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0788
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6771]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xBB28F4F4, 0xD1E4D361, 0x48027F86, 0x42988A9F
Get Chip ID... [MT6771]
Get SOC ID... [7BAC41AC06BC987513EAF4A0ABD95302D3208BC58AA0477D061FECC35711A278]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [9]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x13014E53304A394E381010667D7F567D
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: S0J9N8
EMMC_ID : 0x13014E53304A394E381010667D7F567D
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x0E8F800000 (58.24Gb)
RAM INFO:
INT_SRAM: 0x0000039000 (228.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EXT4] ... OK
Product Brand : ZTE
Product Manufacturer : ZTE
Product Model : ZTE Blade V10
Product Name : ZTE_Blade_V10
Product Device : P671F20
Product Board : pluto
Board Platform : mt6771
Build ID : QP1A.190711.020
Build Date : Fri Jun 19 16:08:44 CST 2020
Display ID : TEL_MX_ZTE_Blade_V10V3.1
Security Patch : 2020-06-05
Version SDK : 29
Version Release : 10
Version Codename : REL
Firmware Version : 20200619.160014
Userdata FS Type : F2FS
Read partition "nvdata"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Read IMEI... OK
IMEI: 8656xxxxxxxxxxx
Repairing IMEI...
IMEI: 8656xxxxxxxxxxx
Patch CERT [NVDATA]... OK
Patch CERT [NVRAM]... OK
Write partition "nvdata"... OK
Write partition "nvram"... OK
Repair Security done!
Y LISTO A COBRAR BIEN...!!!!!
Sale muy sencillo con pandora box, colocan el cable tipo C directo a la box
Seleccionan MTK, seleccione BROM Force (no intente sin este)
Seleccionan IMEI
Colocan el nuevo imei
Seleccionan Reparar
Conectan Botones de VOL+ y VOL-
EL proceso se hace solo.
Dejo LOG:
Selected model: Mediatek Mediatek
Operation: Repair
Software version: 5.0
Host Power Off... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Host Power On... OK
Connect phone to [BOX] in BROM/PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM20 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0788
Get sec config... OK [000000E1]
Active sec flags: [SBC]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6771]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Force switch to BROM... OK
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Waiting for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0788
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6771]
Get sec config... OK [000000E1]
Active sec flags: [SBC]
Release testpoint
Advanced Bypass Security... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM20 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0788
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6771]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xBB28F4F4, 0xD1E4D361, 0x48027F86, 0x42988A9F
Get Chip ID... [MT6771]
Get SOC ID... [7BAC41AC06BC987513EAF4A0ABD95302D3208BC58AA0477D061FECC35711A278]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [9]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x13014E53304A394E381010667D7F567D
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: S0J9N8
EMMC_ID : 0x13014E53304A394E381010667D7F567D
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x0E8F800000 (58.24Gb)
RAM INFO:
INT_SRAM: 0x0000039000 (228.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EXT4] ... OK
Product Brand : ZTE
Product Manufacturer : ZTE
Product Model : ZTE Blade V10
Product Name : ZTE_Blade_V10
Product Device : P671F20
Product Board : pluto
Board Platform : mt6771
Build ID : QP1A.190711.020
Build Date : Fri Jun 19 16:08:44 CST 2020
Display ID : TEL_MX_ZTE_Blade_V10V3.1
Security Patch : 2020-06-05
Version SDK : 29
Version Release : 10
Version Codename : REL
Firmware Version : 20200619.160014
Userdata FS Type : F2FS
Read partition "nvdata"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Read IMEI... OK
IMEI: 8656xxxxxxxxxxx
Repairing IMEI...
IMEI: 8656xxxxxxxxxxx
Patch CERT [NVDATA]... OK
Patch CERT [NVRAM]... OK
Write partition "nvdata"... OK
Write partition "nvram"... OK
Repair Security done!
Y LISTO A COBRAR BIEN...!!!!!
