🔐 Frp Cuenta Google remover cuenta frp Celero 5g con pandora box

[servergsm]

Celero 5g frp cuenta google con pandora box

plataforma meditek
seleccionamos frp
conectamos apagado, presionamos vol - y vol+ al mismo tiempo

Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to [BOX] in BROM mode
Waiting for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0989
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
Get sec config... OK [000000E7]
Active sec flags: [SBC SLA DAA]
Release testpoint
Advanced Bypass Security... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Waiting for device... OK
Driver: [MediaTek Inc.,usbser,MediaTek USB Port,usbser.sys,10.0.17763.3532]
You are using driver version 10.0.17763.3532, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM77 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0989
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xA799B8F0, 0x1AB17586, 0x65DC0CEA, 0x6DEFB63C
Get Chip ID... [MT6833]
Get SOC ID... [8827C8E023792DC747DCC27DAA5095FC1E4FAC51DBF3984ADB2A4252E373333E]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [14]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0xD60103534C443634764084041098887B
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_CNAME: SLD64v
EMMC_ID : 0xD60103534C443634764084041098887B
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0000400000 (4.00Mb)
EMMC_USER : 0x0E67800000 (57.62Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... [EXT4] ... OK
Product Brand : Celero5G
Product Manufacturer : Wingtech
Product Model : WTCELERO5G
Product Name : Jupiter
Product Device : Jupiter
Product Board : S98119AA1
Board Platform : mt6833
Build ID : RP1A.200720.011
Build Date : Thu Dec 8 18:10:32 CST 2022
Display ID : WTCELERO5G_1.13.34
Security Patch : 2022-12-05
Version SDK : 30
Version Release : 11
Version Codename : REL
Firmware Version : SW_S98119AA1_V064
Read partition "frp"... OK
Backup saved to C:/Program%20Files%20(x86)/Z3X/Pandora/Backup/MTK/Mediatek_MT6833/FRP_BACKUP_(2024-4-8_12-22-24)/
Writting FRP data... OK
Erase FRP done!



Selected model: Mediatek Mediatek
Operation: Erase FRP
Software version: 6.7