Online
Este celular cuenta con procesador MediaTek Helio P35 MT6765. En mi caso me llegó con bloqueo de red de la compañía AT&T Mexicano.
Se debe conectar a la box apagado presionando los botones de vol - y vol + para que la box comience el proceso. No dura más de 30 segundos y no consume créditos.
PD: Deben además seleccionar la opción "desbloquear la red", porque si seleccionamos "leer códigos" arroja códigos erróneos.
Selected model: OPPO CPH2239 (Oppo A54)
Operation: Unlock network
Software version: 2.11
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to BOX in BROM mode
Wait for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0766
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Advanced Bypass Security... OK
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM108 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x250ACA63, 0xAAC7044D, 0x7F2A9C08, 0x4AF59785
Get Chip ID... [MT6765]
Get SOC ID... [B4CE855C294667778AE37D1F16874E14755EAC0D986627108A62C75D599AE2F3]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [23]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x13014E53304A394B391026F9486558FD
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_ID : 0x13014E53304A394B391026F9486558FD
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x1D1F000000 (116.48Gb)
RAM INFO:
INT_SRAM: 0x000003A000 (232.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
Check USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Check A/B state... OK
Read product info... OK
Product Board : oppo6765
Board Platform : MT6765
Build ID : QP1A.190711.020
Build Date : Tue Aug 17 21:18:41 CST 2021
Display ID : QP1A.190711.020 release-keys
Security Patch : 2021-08-05
Version SDK : 29
Version Release : 10
Version Codename : REL
Read security partition from phone... OK
Read security files... OK
Read security files... OK
Read lock info... OK
Write lock info... OK
Write security partition to phone... OK
Network Unlock done!
Imágenes(s) Adjuntas
Se debe conectar a la box apagado presionando los botones de vol - y vol + para que la box comience el proceso. No dura más de 30 segundos y no consume créditos.
PD: Deben además seleccionar la opción "desbloquear la red", porque si seleccionamos "leer códigos" arroja códigos erróneos.
Selected model: OPPO CPH2239 (Oppo A54)
Operation: Unlock network
Software version: 2.11
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to BOX in BROM mode
Wait for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0766
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Advanced Bypass Security... OK
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM108 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x250ACA63, 0xAAC7044D, 0x7F2A9C08, 0x4AF59785
Get Chip ID... [MT6765]
Get SOC ID... [B4CE855C294667778AE37D1F16874E14755EAC0D986627108A62C75D599AE2F3]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [23]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x13014E53304A394B391026F9486558FD
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_ID : 0x13014E53304A394B391026F9486558FD
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x1D1F000000 (116.48Gb)
RAM INFO:
INT_SRAM: 0x000003A000 (232.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
Check USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Check A/B state... OK
Read product info... OK
Product Board : oppo6765
Board Platform : MT6765
Build ID : QP1A.190711.020
Build Date : Tue Aug 17 21:18:41 CST 2021
Display ID : QP1A.190711.020 release-keys
Security Patch : 2021-08-05
Version SDK : 29
Version Release : 10
Version Codename : REL
Read security partition from phone... OK
Read security files... OK
Read security files... OK
Read lock info... OK
Write lock info... OK
Write security partition to phone... OK
Network Unlock done!
Imágenes(s) Adjuntas
