Offline
reparar imei Alcatel 3c 2018 5026a/5026d f4 con pandrora box
El teléfono tiene procesador MediaTek MT8321 (Comercialmente hablando, porque en realidad es MT6580).
El proceso es muy simple y no se necesitan ningún tipo de créditos. Se debe conectar apagado a la box y ella misma hace el procedimiento en no más de 20 segundos.
Selected model: Alcatel 5026D (3C)
Operation: Repair
Software version: 2.10
Host Power Off... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Host Power On... OK
Connect phone to BOX in BROM/PRELOADER Mode
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM108 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 6580
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6580]
Library Version [1]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Force switch to BROM... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Wait for device... OK
Read usbhost speed... FULL
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 6580
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6580]
Get sec config... OK [00000007]
Active sec flags: [SBC SLA DAA]
Advanced Bypass Security... OK
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM108 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 6580
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6580]
Library Version [1]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Load DownloadAgent... OK
ME_ID = 0x72F06CB8, 0xD4949EEB, 0xA48FB786, 0xDE6A1AD1
Get sec config... OK [00000000]
Get BROM version... OK
Search DA... OK [11]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Check bootloader answer... OK
Wait for answer from bootloader... OK
Wait for hw detection... OK
Wait DA version... v4.2
Send BROM version... OK
Send storage config... OK
SyncBmtInfoWithDA... OK
Set params... OK
Read flash info... OK
EMMC_ID: 0x4500017045454148091E0138635557B6
Load EMI from phone... OK
Init DRAM... OK
Enable DRAM... OK
Sync with DA... OK
Wait for DA H/W detection... OK
EMMC INFO:
EMMC_ID : 0x700100454841454538011E09B6575563
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0000400000 (4.00Mb)
EMMC_USER : 0x0390000000 (14.25Gb)
RAM INFO:
INT_SRAM: 0x0000020000 (128.00Kb)
EXT_RAM : 0x0040000000 (1.00Gb)
Check USB status... USB_FULL_SPEED
Switching to USB high speed... OK
Wait for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek DA USB VCOM (Android),usb2ser.sys,3.0.1504.0]
High Speed USB detected at COM112
Open port... OK
Check USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Check A/B state... OK
Read product info... OK
Product Brand : TCL
Product Manufacturer : TCL
Product Model : 5026A
Product Name : 5026A
Product Device : A3A_XL_3G
Product Board : mt6737m
Board Platform : MT6580
Build ID : NRD90M
Build Date : Tue Jul 2 18:05:37 CST 2019
Display ID : 01001
Security Patch : 2019-07-05
Version SDK : 24
Version Release : 7.0
Version Codename : REL
Firmware Version : vF5C-0
Get OTP size... OK [0x00800000]
Read OTP... OK
IMEI: 015088XXXXXXXXX
Set new IMEI to:
IMEI: 97288XXXXXXXXXX
Check OTP status... [S_DA_OTP_LOCKED]
Write OTP... OK
Repair Security done!
El teléfono tiene procesador MediaTek MT8321 (Comercialmente hablando, porque en realidad es MT6580).
El proceso es muy simple y no se necesitan ningún tipo de créditos. Se debe conectar apagado a la box y ella misma hace el procedimiento en no más de 20 segundos.
Selected model: Alcatel 5026D (3C)
Operation: Repair
Software version: 2.10
Host Power Off... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Host Power On... OK
Connect phone to BOX in BROM/PRELOADER Mode
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM108 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 6580
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6580]
Library Version [1]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Force switch to BROM... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Wait for device... OK
Read usbhost speed... FULL
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 6580
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6580]
Get sec config... OK [00000007]
Active sec flags: [SBC SLA DAA]
Advanced Bypass Security... OK
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM108 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 6580
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6580]
Library Version [1]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Load DownloadAgent... OK
ME_ID = 0x72F06CB8, 0xD4949EEB, 0xA48FB786, 0xDE6A1AD1
Get sec config... OK [00000000]
Get BROM version... OK
Search DA... OK [11]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Check bootloader answer... OK
Wait for answer from bootloader... OK
Wait for hw detection... OK
Wait DA version... v4.2
Send BROM version... OK
Send storage config... OK
SyncBmtInfoWithDA... OK
Set params... OK
Read flash info... OK
EMMC_ID: 0x4500017045454148091E0138635557B6
Load EMI from phone... OK
Init DRAM... OK
Enable DRAM... OK
Sync with DA... OK
Wait for DA H/W detection... OK
EMMC INFO:
EMMC_ID : 0x700100454841454538011E09B6575563
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0000400000 (4.00Mb)
EMMC_USER : 0x0390000000 (14.25Gb)
RAM INFO:
INT_SRAM: 0x0000020000 (128.00Kb)
EXT_RAM : 0x0040000000 (1.00Gb)
Check USB status... USB_FULL_SPEED
Switching to USB high speed... OK
Wait for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek DA USB VCOM (Android),usb2ser.sys,3.0.1504.0]
High Speed USB detected at COM112
Open port... OK
Check USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Check A/B state... OK
Read product info... OK
Product Brand : TCL
Product Manufacturer : TCL
Product Model : 5026A
Product Name : 5026A
Product Device : A3A_XL_3G
Product Board : mt6737m
Board Platform : MT6580
Build ID : NRD90M
Build Date : Tue Jul 2 18:05:37 CST 2019
Display ID : 01001
Security Patch : 2019-07-05
Version SDK : 24
Version Release : 7.0
Version Codename : REL
Firmware Version : vF5C-0
Get OTP size... OK [0x00800000]
Read OTP... OK
IMEI: 015088XXXXXXXXX
Set new IMEI to:
IMEI: 97288XXXXXXXXXX
Check OTP status... [S_DA_OTP_LOCKED]
Write OTP... OK
Repair Security done!
Debes estar registrado para ver imágenes adjuntar
Debes estar registrado para ver imágenes adjuntar
